This great article below on the subject of Installing A Bathtub is definitely intriguing. Try it and make your own ideas.
Installing a bath tub isn't precisely rocket science, but it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is readily easily accessible, the job can relocate speedily; if you have to open a wall to get rid of the old tub as well as place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will require a helper to vacate the old tub and set in the new one. Make sure you have certified on your own for the task and also fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to think about using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will assist you mount a brand-new bath tub in your shower room if you have currently acquired a brand-new tub and don't need to change the arrangement of your previous supply of water pipes.
Your devices as well as material checklist need to consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain any kind of water staying in the system. The procedure of removing the existing faucets can be fairly troublesome due to the limited accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place between the faucet and also the sink. Secure the tap in place with the manufacturer supplied backnut. Once the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind needs to be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wooden boards under its feet, place the bathtub in the required setting. The wooden boards are valuable in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit all-time low of the outermost versatile tap port to the appropriate supply pipe by making a compression join; after that do the same for the other faucet.
Activate the water system and check all joints and also brand-new pipework for leaks as well as tighten them if required. Load the tub as well as additionally check the overflow outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub must wait until the bath tub has actually been used a minimum of once as this will certainly resolve it into its last position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with moisture and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and also cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture fairly early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the marketplace. It is advisable to fit the floor tiles using water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very eager about Tools You Need to Install a New Bathtub and I really hope you enjoyed reading the entry. Liked our entry? Please share it. Help another person locate it. Thank you so much for going through it.
Don't delay, ring today!